(+34) 647 812 195
|
SpeedoHealer kit SH-V4 + SH-U01 (universal). This product is compatible with these bikes:
What is a "SpeedoHealer"?A SpeedoHealer allows you to calibrate the speedometer and correct both the inherent factory error and the errors caused by changing the sizes of the pinion, chainwheel and wheels. It is the most reliable and flexible speedometer calibrator available, compatible with any bike having an electronic speedometer. Why use a SpeedoHealer?Correct the Error of the Speedometer/OdometerOn a modern sportsbike, the margin of error inherent in the factory speedometer can be as much as 10%. A SpeedoHealer will calibrate your speedometer/odometer to compensate for these errors and show a true value for your speed and total mileage. Remove a Speed LimitationSome vehicles have a speed limiter, for example Can-Am ATVs, Honda CBR1000RR / VFR800X / VFR1200F, Kawasaki ZX-10R / ZX-12R / ZX-14 / ZZR140, Polaris ATVs, Yamaha FZ-09 / MT-09 / YZF-R1 / V-Max (and many others). For race use, a SpeedoHealer can prevent the limiter from activating (by increasing the limit). Although all SpeedoHealers have two memories, the SpeedoHealer V4-AB (manual switch) or the SH-TSD (automatic switch) are the most appropriate modules for this use. Convert the speedometer display to show km/h or mphNo need to guess your speeds when you are travelling across different countries with different speed limit displays. A SpeedoHealer will convert from km/h at the press of a button (conversion from mph to km/h requires a conversion factor to be used +60.9%). Calibrate a Replacement SpeedometerA replacement speedometer may not work correctly with the original/unmodified signal from the vehicles speed sensor. A SpeedoHealer can modify that signal to allow the speedometer to work correctly, or it can be used with an external speed sensor (SpeedoHealer cable SH-WSS). Show off your Last Top SpeedAn external Top Speed button is included with the SpeedoHealer V4-TS/V4-C. Pressing the button will cause the speedometer to show the last top speed recorded...no more arguments! Bike-Specific Information
SpeedoHealer Features
InstallationInstallation and Programming The installation process is usually very easy, requiring only three steps. 1) Connect the SpeedoHealer Plug n' Go harness into the speed sensor cableFor most bikes a SpeedoHealer Plug n' Go harness is available. These have the same connectors as the bike in question and so can just be plugged into the cable from the bike's speed sensor, allowing the signal to pass through the SpeedoHealer for modification, without cutting or jointing any wires. The main exceptions are some Yamaha models with ABS or bikes that use uncommon connectors. Always consult the Healtech Product Advisor prior to purchase to confirm the recommended cable for your vehicle. If you have a doubt, please contact us. There are many installation guides available on the Healtech website (scroll down to see the guides titled "SH-...") 2) Connect the SpeedoHealer module and perform the setup checksThe SpeedHealer has a test mode to: a) check the SpeedoHealer is receiving the speed signal and b) check the SpeedoHealer is sending the modified signal to the speedometer. 3) Program a correction factor to correct the errorEvery vehicle is different and so requires a different correction factor. The best method to find out the current error is to do a short distance at a fixed speed and compare the speedometer value with a GPS value. Alternatively you can calculate an estimated correction factor. - Online in www.healtech-electronics.com SpeedoHealer Cable HarnessA compatible SpeedoHealer harness is always required to allow the vehicle's speed signal to pass through the SpeedoHealer module for correction. For most bikes a "Plug n' Go" harness is available which has the same original-style connectors as the vehicle and so a SpeedoHealer module can be connected to the speed sensor without any cutting or jointing of the original wiring or requiring additional power connections. In almost all cases, the SpeedoHealer module can use the power and ground connection supplied by the ECU. However, this is not always possible if the vehicle has an uncommon style of connector or the cable carrying the speed signal is part of the main ECU wiring harness (as for bikes with ABS), and so the correct wire must be cut and a universal harness be used to bridge the signal through the SpeedoHealer module. High-quality 3M jointing connectors are provided with the universal harnesses. SpeedoHealer VersionsThere are three universal versions that offer different extra features, and three special versions for specific vehicles. SpeedoHealer SH-V4 - universal module with a Top Speed buttonThis unit is the standard SpeedoHealer and includes an (optional) external button which, when pressed, displays the last top speed on the speedometer. SpeedoHealer V4-AB - universal module with an external A/B memory switchThis unit includes an external switch which allows the rider to change between memory A and B with different calibration factors. A typical use for this option would be to use SpeedoHealer V4-TSD - universal module with automatic A/B memory switchingThis unit can make the A->B memory change automatically at a specific, programmable speed. A typical use for this option would be to use SpeedoHealer V4-C - special module only for specific bikesSpeedoHealer V4-2W - special module only for specific Yamaha bikes with a two-wire inductive speed sensorSpeedoHealer V4-2WA - special module for specific Honda bikes with a two-wire inductive speed sensor          For more information, please visit this product's webpage. Currently Viewing Product 127 of 129 |
