Your Bike:

Headlight Shields, "Second Skin" Type - CFMoto 700CL-X Heritage 2021 onwards / 700CL-X Sport 2022 onwards / 700CL-X Adventure 2023 onwards, Husqvarna Vitpilen 401 2024 onwards

  • Model: RG-HLS0179CL
  • Manufactured by: RG Racing

19,95€
(including IVA)

A generic image delivery 3-7 working days (mainland Spain)

This R&G Headlight Shield is made from a "Second Skin" Film and specially designed to fit specific bike models.

This product is compatible with these bikes:

  • CFMoto 700CL-X Adventure - 2023 onwards
  • CFMoto 700CL-X Heritage - 2021 onwards
  • CFMoto 700CL-X Sport - 2022 onwards
  • Husqvarna Vitpilen 401 - 2024 onwards

R&G Racing "Second Skin" is a flexible (stretchable) polyurethane film that is almost unbreakable and will protect your bike from small impacts such as stone chips and gravel from the road, and general abrasions and scratches from your jacket zipper, knees, and boots! It is also a barrier against road salt and tar.

The film is self-adhesive and is applied with a soap solution for easy positioning. While the adhesive is strong, the film can be easily removed in a single piece and leaves no residue.

Second Skin stretching with pointer Second Skin - cut sheet Second Skin - ready to apply Second Skin - fitted with logo

Paint protection films have traditionally been used on race vehicles to maintain the custom sponsor paintwork in perfect condition throughout the race and on the most expensive luxury cars.
Now it is often found in small sections protecting the paintwork around car wheels but is essential for motorcycles having so many exposed surfaces.

The film is normally used to protect the most vulnerable surfaces such as:

Features

  • Almost unbreakable
  • Kit is precision-cut for specific motorcycles
  • High strength adhesive but leaves no reside when removed
  • Can be stretched over curved surfaces due to the high strength adhesive
  • Manufactured from high-quality, clear polyurethane
  • Does not "yellow" with long-term exposure to the sun

Kit Contents

  1. Pre-cut self-adhesive pieces.
  2. Alcohol wipe for surface preparation.
  3. Soap solution for easy/accurate positioning of the pieces.
  4. Plastic "squeegee" for removing air from film/fixing film.
  5. Instructions

Installation

The pieces in the pre-cut kits are designed to be easily-manipulated and installed by the home-user.
The material has a high elasticity to allow it to be easily stretched over bodywork curves. The film uses a special adhesive that although strong, can be removed leaving NO residue whatsoever.

  1. Clean the surface.
  2. Moisten the surface with the supplied solution.
  3. Moisten your fingers to prevent finder marks on the adhesive.
  4. Remove the backing layer.
  5. Place the piece on the wet surface and slide the piece to its correct position.
  6. Moisten the exterior surface of the piece to allow the squeegee to slide over the surface easily.
  7. Squeeze out the air bubble and moisture from under the film to allow the adhesive to touch the surface.
  8. To stretch a piece over a curve, fix on section securly before stretching the remainder of the piece over the curve. Using pure water instead of the soap solution will allow the adhesive to bond faster. The adhesive bonding time can be reduced using a hair dryer, to enable quick adhesion to tight curves.

Second Skin - Unboxing and Installation 1

Second Skin - Unboxing and Installation 2

Paint Protection Film Users

Second Skin / Eazi-Guard is currently protecting many of the leading race teams in BSB, WSB and Road Racing including HRC, Milwaukee BMW, JG Speedfit Kawasaki, MV Augusta Racing, Tsingtao Racing and Quattro Plant Kawasaki.
Eazi-Guard™ is sponsoring the Yamaha Europe R3 and R125 cup, with all bikes featuring Eazi-Guard™ protection. It is also extensively used at the NW200 and Isle of Man TT races.

Eazi-Guard Sponsored Teams: Road Racing | Short Circuit

Universal Sheets

Both R&G "Second Skin" and "Eazi-Guard" are manufactured by Eazi-Grip Racing Products in the UK and the material is available in sheets with pre-cut sizes for general use.

Standard sheet: 50cm x 71cm
Large sheet: 48cm x 139cm


How to find R&G products for your bike?

Given the huge range of products it is really not practical to just browse/look for the product(s) that may be compatible for your bike and so we strongly recommend you FIRST find the R&G product model number by one of the following methods.

  • Use this up-to-the minute R&G compatibility document (pdf) to find the products compatible with your bike
  • Or, look in the R&G Racing website to find the products compatible with your bike.
  • Or, use the above drop-down menu "Show Products for..." to find all our compatible products for your bike, including those from R&G Racing (due to constant and rapid product development by R&G, this section may not include all the currently available products).

Once you know the R&G product model number eg. LP0108BK, just start typing the model into the search field at the top of this page and the product should be listed in the popup results.

If you cannot find a product, please don't hesitate to Contact Us as it may be a new product we have not yet included in our shop.