DENALI DR1 Hi-Power LED Light Kit

The Denali DR1 TriOptic™ LED Light kit is designed to provide the maximum forward beam possible, over 300m of forward view!

The system comprises two tough metal housings each equipped with a 10W Cree high-power LED and an oversized internal rear reflector. The housings are made from aluminium with a black powder-coated finish and have cooling fins cast into the body for maximum heat dissipation. The front bezels are tough polycarbonate for resistance against stone damage.

Light Coverage

The kit includes two different pairs of lenses: Spot and "True-Hybrid"™ to provide three types of light coverage.

1 - Spot Beam Pattern

Each housing is fitted with the same Spot lens plates.

The housings are supplied from the factory with these lenses already fitted as this is the most common configuration.

This provides a 300m forward beam with 23m wide side-coverage.

2 - Spot-Hybrid Beam Pattern

Each housing is fitted with a different lens plate: one with a "True-Hybrid"™ and the other with a Spot lens.

This provides a 270m forward beam with 36m wide side-coverage.

3 - "True-Hybrid"™ Beam Pattern

In this configuration, each housing uses the same "True-Hybrid"™ lens plates.

This provides a 162m forward beam with 50m wide side-coverage. The "True-Hybrid"™ lenses are CE-marked.

How are the lights controlled?

The lights are controlled by a high-quality, waterproof On/Off switch, included in the kit.

It is also possible to use the lights at half intensity and/or controlled by the vehicle's original main-beam switch by using additional accessories (not included in the kit): see the Optional Upgrades section below.

Installation

Due the size of the DR1 housings, they are normally fitted to crash bars or other types of robust bike protection systems.

Installation Instructions: English

All products supplied by Motorvista include instructions in english and spanish.

Kit Contents

• DR1 LED light housings x 2
• "True-Hybrid"™ lens plates (CE-Mark approved) x 2
• Spot lens plates (pre-installed in the housings) x 2
• HotSwap™ single intensity wiring harness x 1
• DrySeal™ waterproof illuminated switch x 1
• Switch support for 22mm (7/8in) handlebars x 1
• Switch support for 25mm (1in) handlebars x 1
• Housing brackets with M8 fixings x 2
• Cable ties x 4
• Adhesive square x 1

Specifications

• LED Types: 10W Cree XPL HI LED x 2
• Current Consumption: 1.6 amps
• Spot Beam Reach: 300m
• Spot Beam Width: 23m
• Total Light Output: 2190 Lumens
• Operating Voltage: 12 Vdc
• Dimensions of Light Housings: 9.4cm diameter x 9.6cm deep

Also Available (optional) Amber Lens Plates for the DENALI DR1

Blue light is reflected by fog/water vapour/rain. The DENALI Amber Lens Plates filter out the blue component from the LED white light and so improve visibility in fog and rain.

This kit includes two pairs of lenses:
"True-Hybrid"™ lenses x 2
"Spot" (four spot lenses) x 2

The amber lenses for the DR1 lights are available here.

Supports for DENALI lights: see the DENALI website for options.

DENALI 2.0 Lights - Common Characteristics

High Power LEDs - HiDrive™

The LEDs used in all DENALI 2.0 systems are the latest generation "Hi-Intensity" LEDs from Cree.

Compared to the DENALI 1.0 series, these produce 20% more light (lumens) for the same low current consumption.

Advanced Thermal Management - LiveActive™

LEDs last longer and output more light when they are kept cool. The DENALI 2.0 lights have advanced software control "LiveActive"™ integrated into the LEDs and external oversize heatsinks cast into the housing to maximise the efficiency minute-by-minute and ensure the longest lifetime.

Multi-Beam Lens system - TriOptic™

All kits include two spot lenses and two flood lenses to allow a choice of three lighting patterns. Use two spot lenses for the maximum forward reach, two elliptical floods for maximum side spread, or one of each for a combined effect.

In addition to providing three beam options in one kit, the second set of spot-only lenses are CE-certified. This ensures you can stay street-legal on-road while maintaining the option for maximum distance off-road.

Fully Waterproof Construction - DrySeal™

The seals between the components of the housings are moulded silicon and the cable entry points are potted in epoxy to ensure the housings are 100% watertight even when submerged. The control switches (On/Off and Off/Low/High) are also 100% waterproof.

Corrosion-Proof Bezels - Impact PC™

The front bezels always bear the brunt of stone damage and so the coated aluminium of the main housing is not always an appropriate material. The housing bezels are moulded in 100% polycarbonate (DR2, DM and DR1 only/not D4) for the best possible resistance to stone damage, providing a tough surface that does not rust or fade with the sun.

Chromed Reflectors

The internal LED holders are plated in high reflective chrome to focus all the generated light forward and to better match the bike's original headlights

Low-profile mounts and stainless-steel fixings

The hinged mounts are designed to reduce the installed profile to the minimum possible while maintaining high strength. All screws and nuts are manufactured in stainless-steel.

Waterproof Switch – "DrySeal"™

All DENALI switches are completely waterproof to ensure a long lifetime in harsh, outdoor conditions. The switches can be mounted on a flat surface or a handlebar (22mm/25mm).

HotSwap™ Wiring Harness

The cabling uses high-quality waterproof components and allows a simple upgrade to dual intensity LEDs by the use of the DataDim™ Controller Relay (available here).

---

Optional Upgrades

DataDim™ Controller

This relay allows the lights to be switched between Off/Low Intensity/High Intensity.

The lights are switched Off/On by the standard switch included in this kit.
The Low/High intensity is controlled by the original main beam switch of the motorcycle via a connection to the original main beam circuit.

The DataDim™ controller relay (available here) replaces the Single-Intensity relay that is included in the kit.

DataDim™ Controller + Hi/Low/Off Switch

This option provides full control of the lights independently of the main beam control.

In some motorcycles it is impossible to use the main beam control and so this manually-operated switch is required.
This option replaces the standard Single-Intensity relay with a DataDim relay (available here) and replaces the standard Off/On switch with the Off/Low/High switch (available here).

Switch Eliminator

This allows the lights to automatically switch on with the ignition circuit, so are always on when riding. This option replaces the standard On/Off switch and is available here.

Harness Extension

This cable extends the length of the standard lighting harness by 61cm (24") and features the same high-quality waterproof connectors as the original DENALI cables. It is available here.

Y-Splitter Kit

If you wish to add one or two more lights to your existing DENALI system, the "Y" splitter kit makes that very easy. It is available here.

Auxiliary LED Brake light

The B6 LED auxiliary brake light is a great safety addition to your existing brake light to wake up those cage-drivers! The unit comprises six 0.5W LEDs in a very compact, low-profile housing and is available here.

DENALI Light kits Comparison

DENALI Lights - EU Compliance